Checking the air-mass sensor - symptoms, cause of failure & troubleshooting

Air-mass sensor

10037926a_AM0_white_inclined

The air-mass sensor calculates the intake air mass in internal combustion engines. The engine control requires this variable in order to control a wide range of functions. This page explains the design and function of the air-mass sensor. You will also find information about how a faulty air-mass sensor can manifest itself, the causes leading to its failure, and how it can be checked in the workshop.

The following technical information and practical tips have been compiled by HELLA in order to provide professional support to vehicle workshops in their day-to-day work. The information provided on this website is intended for suitably qualified personnel only.

Air-mass sensor function

The air-mass sensor is used to measure the intake air mass. It consists of a tubular housing with flow straightener, sensor protection, and sensor module. It is mounted in the intake pipe between the air filter housing and the intake manifold.

Two temperature-dependent metal film resistors affixed to a glass membrane are arranged in the air flow. The first resistor (RT) is a temperature sensor and measures the air temperature. The second resistor (RS) is used to detect the air flow rate. The resistor RS cools down to a greater or lesser degree depending on the intake air flow. In order to balance out the constant temperature difference between resistors RT and RS, the current flow through resistor RS must be dynamically regulated by the electronics. This heat flow is used as a measured variable for the respective air mass that is taken in by the engine. This measured value is required by the engine management control unit to calculate the fuel quantity required.

Testing the mass air flow sensor

Testing the mass air flow sensor: Example OK — Air-mass sensor – Example OK

The following test steps should be considered during troubleshooting:

1

Checking the plug connection

Check plug connection for tight fit and correct contact.

2

Checking the air-mass sensor

Check the air-mass sensor for damage.

3

Checking the measuring elements

Check the measuring elements for damage.

4

Checking the voltage supply

Check the voltage supply

5

Checking the connecting cables

Check the connecting cables between the removed control unit plug and the sensor plug for continuity (circuit diagram required for pin assignment). Reference value: approx. 0 ohms.

6

Electronic test of the air-mass sensor

Electronic test of the air-mass sensor through the engine management control unit. When a fault occurs, a fault code is stored in the control unit that can be read out using a diagnostic unit.

Not helpful at all

5

4

3

2

1

Very helpful

Spare Parts Finder

Licence Plate Manual vehicle identification OE-No.

Spare Parts Finder

Simple vehicle identification with licence plate number Also determine spare parts with OE numbers Detailed product information Find wholesalers near you

You might also be interested in

Basic Knowledge

Overview of driver assistance systems

Driver assistance systems at a glance: from ACC and glare-free high beam to lane departure warning - everything for the workshop.

Reading time: 2 minutes

Basic Knowledge

Programming car keys and changing batteries

How does a remote control key work? Everything about the structure, coding and programming, explained using the example of a VW Golf 5.

Reading time: 5 minutes

Basic Knowledge

Keyless Go & Keyless Entry system

Introduction to the Keyless Go system - from function and possible faults to diagnostics, ideal for vehicle workshops.

Reading time: 12 minutes

Basic Knowledge

Secondary air injection system: faults & overview

Structure and function of the secondary air system, common fault symptoms and causes of failure - knowledge for your workshop.

Reading time: 5 minutes

Basic Knowledge

Lane change assist

Learn all about the lane change assistant - diagnostic and repair instructions, supplemented by a clear video.

Reading time: 13 minutes

Basic Knowledge

Service work on the charging system

Step-by-step instructions for servicing the charging system, including visual inspection and signal testing on the controller.

Reading time: 6 minutes

Basic Knowledge

Activated charcoal canister – facts & info

Everything about the activated charcoal container: how it works, typical fault symptoms and causes in the event of a fault - including workshop tips.

Reading time: 2 minutes

Basic Knowledge

ABS and ESP control units

Important basics and diagnostic information for ABS and ESP control units - everything your workshop needs for repairs.

Reading time: 4 minutes

Basic Knowledge

Media pump - design, function and troubleshooting

Find out more about the function and system integration of the medium pump as well as testing and repair options.

Reading time: 7 minutes

Basic Knowledge

Check multi-function regulator

Find out how to check the multifunction regulator, measure the generator voltage and ensure that the regulator is functioning correctly.

Reading time: 4 minutes