Transmission range sensor circuit

The transmission range sensor determines the transmission speed. The transmission control system uses this information to, for example, calculate which gear is required and the shifting time. Scroll through this page and find out about common variants, their functional principle, and how you can check transmission range sensors using simple methods.

Important safety note

The following technical information and practical tips have been compiled by HELLA in order to provide professional support to vehicle workshops in their day-to-day work. The information provided on this website is intended for suitably qualified personnel only.

1. Functional principle

How transmission range sensors work

Transmission range sensors record the transmission speed. This information is required by the control unit to regulate the shifting pressure when shifting gears and to decide which gear needs to be engaged at which point.

There are two types of transmission range sensor design: Hall generators and inductive sensors.

The rotation of the ring gear changes the magnetic field, which, in turn, changes the voltage in the transmission range sensor. These voltage signals are forwarded to the control unit by the transmission range sensor.

2. Symptoms

Transmission range sensor faulty

A faulty transmission range sensor can manifest itself as follows:

  • Failure of the transmission control system, the control unit switches to an emergency program
  • Engine indicator lamp comes on
3. Cause of failure

Causes of faulty transmission range sensors

Causes of failure can be:

  • Internal short circuits
  • Breaks in wiring
  • Short circuits in wiring
  • Mechanical damage to the encoder wheel
  • Contamination caused by metal abrasion
4. Troubleshooting

Checking the transmission range sensor

The following test steps should be considered during troubleshooting:

1

Check the sensor

Check the sensor for contamination

2

Check the encoder wheel

Check the encoder wheel for damage

3

Read out fault memory

Read out the fault memory

4

Measure the resistance of the inductive sensor using an ohmmeter

Reference value at 80°C: approx. 1,000 ohms.

5

Check the supply voltage to the Hall generator using a voltmeter

(circuit diagram for pin assignment required).

Attention:
Do not measure the resistance on the Hall generator as doing so could destroy the sensor.

6

Check the continuity of the sensor's connecting lines between the control unit connector and sensor connector

(circuit diagram for pin assignment required).

Reference value: 0 ohm.

7

Check the sensor's connecting lines for a short circuit to frame

With the control unit connector pulled out, measure against vehicle ground at the sensor connector using the ohmmeter.

Reference value: >30 MOhm.

Cât de util ți se pare acest articol?

Nu este deloc util
5
4
3
2
1
Foarte util
Succes

Captcha incorectă

Captcha incorectă

Eroare

A apărut o eroare

Căutare piese de schimb
Nr. OE Identificarea manuală a vehiculului
Cei mai importanți producători
Alți producători
Seria de vehicule Înapoi
Vehicul Înapoi

Introduceți numărul OE în câmpul de introducere. De obicei, numărul OE se găsește pe piesa de schimb însăși sau în documentele vehiculului.

Căutare piese de schimb
De asemenea, identificați piesele de schimb cu numerele OE Informații detaliate despre produs Găsiți distribuitori en gros în apropierea dumneavoastră
dummy
Processing Selected Car
Poducători
Seria de vehicule
Vehicul
Puterea motorului
Cilindreea motorului
Tipul de combustibil
Anul de construcție
Codul motorului

Alegeți categoria:
Înapoi
dummy
Distribuie
Trimite prin Copiază linkul
Adresa URL a fost copiată în clickboard!
Numărul articolului
Number
Numărul articolului a fost copiat!
Căutare pe internet Instrucțiuni de montare
Mai multe detalii
Denumirea produsului Valoare
Mai puține detalii

Dealerul dumneavoastră
Autoteile Krammer GmbH
dummy
Lechstraße 1-3
68199 Mannheim
Afișează harta