Idle speed regulator / idle speed control: Function, fault symptoms and troubleshooting

The idle speed controller ensures that the idle speed of the engine remains constant in all load conditions. On this page you can find out about how the idle speed actuator regulates the intake air mass of the engine, and how the failure of this actuator impacts on the engine running. Practical tips for troubleshooting and assembly instructions help to quickly rectify defects relating to the idle speed controller.

Important safety note

The following technical information and practical tips have been compiled by HELLA in order to provide professional support to vehicle workshops in their day-to-day work. The information provided on this website is intended for suitably qualified personnel only.

1. Functional principle

Idle speed controller function

The idle speed actuator is a bypass air valve. The idle speed actuator shown as an example consists of a closed cast housing with flange-mounted solenoid valve servo unit. Attached to this is a nozzle holder, which releases different air cross sections by moving the servo unit, and can therefore control the air mass flow when the throttle valve is closed.

The idle speed actuator is responsible for regulating the engine speed as part of the overall idle-speed control of the engine management system. If there is a sudden change to the engine load condition when in idle mode (e.g. air-conditioning system being switched on, creep speed in 1st gear, or activation of another electrical consumer), air and fuel are also required in order to prevent the engine from stopping. If the engine speed falls below a certain critical value, which is stored as a constant in the control unit memory, the solenoid valve is activated and an increased air flow rate is achieved. The opening time of the injection valves is simultaneously extended and adapted to the engine's requirements.

2. Symptoms

Symptoms of a faulty idle speed controller

A faulty idle speed actuator can manifest itself as follows:

  • Fluctuating idle speed
  • Engine stops running at idle speed
  • Engine stops running at idle speed and activation of additional consumers
  • Engine indicator lamp comes on
3. Cause of failure

Causes for faulty idle speed controllers

Causes for failure of the idle speed actuator can be:

  • Contamination / resin formation
  • Short circuits in the coil
  • Electric magnetic drive becomes stuck
  • No voltage supply from the engine management control unit
4. Troubleshooting

Checking the idle speed actuator

The following test steps should be considered during troubleshooting:

1

Checking the voltage supply

Check the voltage supply with the ignition switched on.

  • Measured value: 11 – 14 V.

Note:
An Ohm measurement must only be carried out in a de-energized state (plug connection removed).

2

Measuring the coil resistance

Use the multimeter to measure the coil resistance between the two connection pins of the idle speed actuator.

  • Reference value = approx. 10 ohms (observe manufacturer's specifications).

3

Checking the coil for winding short circuit

Check the coil for a winding short circuit between the two connection pins.

  • Measured value in the event of a short circuit = 0 ohms.

4

Checking the coil for winding interruption

Check the coil for a winding interruption between the two connection pins.

  • Measured value in the event of an interruption = >30 MOhm.

5

Checking the coil for short circuit to frame

Check the coil for short circuit to frame – between pin 1 and component housing, and between pin 2 and component housing.

  • Measured value in the event of an unimpaired coil = >30 MOhm.

6

Mechanical check

Unscrew the servo unit from the housing. Visual check to determine whether the bypass opens and closes when the valve rod is actuated.

7

Read out fault code

Read out fault code.

ASSEMBLY INSTRUCTIONS

Before mounting the idle speed actuator, the supporting surface must be cleaned and, if necessary, the flange seal must be replaced.

Observe the tightening torque!

  • Fixing screws 12 – 15 Nm

Please observe the specifications provided by the respective vehicle manufacturer.

Cât de util ți se pare acest articol?

Nu este deloc util
5
4
3
2
1
Foarte util
Succes

Captcha incorectă

Captcha incorectă

Eroare

A apărut o eroare

Căutare piese de schimb
Nr. OE Identificarea manuală a vehiculului
Cei mai importanți producători
Alți producători
Seria de vehicule Înapoi
Vehicul Înapoi

Introduceți numărul OE în câmpul de introducere. De obicei, numărul OE se găsește pe piesa de schimb însăși sau în documentele vehiculului.

Căutare piese de schimb
De asemenea, identificați piesele de schimb cu numerele OE Informații detaliate despre produs Găsiți distribuitori en gros în apropierea dumneavoastră
dummy
Processing Selected Car
Poducători
Seria de vehicule
Vehicul
Puterea motorului
Cilindreea motorului
Tipul de combustibil
Anul de construcție
Codul motorului

Alegeți categoria:
Înapoi
dummy
Distribuie
Trimite prin Copiază linkul
Adresa URL a fost copiată în clickboard!
Numărul articolului
Number
Numărul articolului a fost copiat!
Căutare pe internet Instrucțiuni de montare
Mai multe detalii
Denumirea produsului Valoare
Mai puține detalii

Dealerul dumneavoastră
Autoteile Krammer GmbH
dummy
Lechstraße 1-3
68199 Mannheim
Afișează harta