Golf 6 rear combination lamp encoding

Here you will find useful information and handy tips relating to encoding LED rear combination lamps based on a Golf 6.

The exterior lighting on a vehicle offers a wealth of opportunities for customising the vehicle. Retrofitting LED rear combination lamps is a very popular modification. However, on modern vehicles it isn't enough to simply replace the lamps. In many cases the cables also need to be adjusted and the vehicle electric system control unit needs to be encoded accordingly. This page explains the work that needs to be done in these cases using the example of a Golf 6.

Important safety note The following technical information and practical tips have been compiled by HELLA in order to provide professional support to vehicle workshops in their work. The information provided on this website is intended for use by suitably qualified personnel only.

 

ENCODING THE GOLF 6 LED REAR COMBINATION LAMP: BASIC PRINCIPLES

The number of different vehicle types is increasing from year to year. The success of “niche models” is further softening the delineation between traditional classifications such as station wagon, sedan, or van. In addition, new developments in the fields of driver assistance, communication, and safety systems are creating further distinctive features to fulfil customer wishes.

 

Modifications and tuning of the exterior lighting are in the Top 10 of customer wishes – particularly since the introduction of daytime running lights. Conversion to xenon headlights or LED rear combination lamps are also in demand.

 

However, the challenges involved in the installation of such lighting systems increase with the complexity of the products.

 

For some years now, control units have been controlling, regulating, and monitoring lighting functions. If different lamps or headlamps are installed in the vehicle, the control unit has to be “informed”. This is where “encoding” comes into the picture. During encoding, parameters are changed in the respective control unit to guarantee perfect operation of the lighting functions.

 

Example of HELLA Golf 6 LED rear combination lamp

In addition to the HELLA rear combination lamps, adapter cables are always required since LED lamps have different connections. These adapter cables are relatively easy to make yourself.

 

The following items are required for complete conversion:

  • HELLA, exterior LED rear combination lamps no. 2SD 010 408-071 left / -081 right
  • HELLA, interior LED rear combination lamps no. 2SA 010 409-131 left /ft2TZ 010 409-141 right
  • Connector for connection to the LED lamps VW no. 4x 7N0 972 703
  • Socket for connection to the wiring harness VW no. 4x 191 972 713
  • Crimp contacts HELLA no. 8KW 863 931-003
  • Individual wires with crimped contacts VW no. 6x 000 979 150 EA

MAKING THE ADAPTER CABLES: INSTRUCTIONS

Cut the cables in the middle

Cut the 6 cables in the middle so that you have 12 cables: One end with a crimp contact, the other without contact. Then shorten the cables to approx. 10 cm.

Click the cable ends into the connector

Click the cable ends equipped with the blade terminals into the connector (7N0 972 703) for the LED lamps.

Strip the cable ends and crimp contacts in place

Strip the other cable ends by approx. 6 mm and crimp contacts 8KW 863 931-003 in place. You will need a pair of pliers for non-insulated crimp contacts for this (HELLA no. 8PE 002 007-011).

 

During this working step, make sure that the LED connector with the red locking hoop is at the top and the crimp contacts are aligned evenly to one another. This prevents the cables twisting during subsequent connector assembly.

Click the cable ends into the socket

Click the cable ends with the blade terminals into the socket (191 972 713). Make sure the cables are in the right order! (Red locking hoop from connector and chamber numbers 1, 2, 3 from the socket must be visible from above).

Repeat the working steps

Now repeat these working steps for the other three adapters

INSTALLING THE LAMPS IN THE VEHICLE: INSTRUCTIONS

Pull off the side panel

Open the trunk lid. Pull the side panel in the trunk backward and off so that the knurled-head screw is easy to reach.

Remove the light

Unlock the contact plug and remove it from the light.

Unscrew the knurled-head screw from the light

Pull the light backward and out of the body

Insert the adapter

Insert the adapter into the LED light (exterior light). Then push the red locking hoop to the limit stop toward the light.

Insert the LED light

Insert the LED light into the body and tighten using the knurled nut.
Caution! Heed the guides on the light during insertion.

Connect the socket with the connector

Connect the adapter socket with the connector from the vehicle harness

Remove the flap

Unlock and remove the flap from the trunk lid.

Loosen the M8 screws on the light

Caution! Unlatch the plastic strip on the side of the light and remove downward.

Insert the inner LED light

Insert the inner LED light into the body and tighten using the M8 screws. Click the plastic strip back onto the light.

Connect the adapter

Connect the adapter with the light and the vehicle harness.

Install the removed parts

Install all the removed parts in reverse order.

ENCODING: INSTRUCTIONS

On account of the different characteristics of lamps with filament bulbs and lamps with LEDs, the control unit – known as “Body Control Module” (BCM) at VW – has to be “encoded”. Parameters are changed in the control unit in such a way that the LED rear combination lamps work perfectly. If this does not happen, fault messages will appear on the display and lamps will only have limited functionality. (The stop light in the tailgate can shine more brightly than the stop light in the exterior lamps).

 

Caution!
Conversion is not possible with every BCM. There are different specifications for the Golf VI concerning the production date (vehicle) from which perfect functionality of the lighting functions is guaranteed. Before a vehicle is converted to LED lamps, we recommend reading out the BCM software version (see Figure 9).

 

Generally speaking, there are two different BCMs: The old one with software version 03XX. Proper conversion is not possible with this BCM. If a customer would still like to equip their vehicle with LED lamps, a new BCM will have to be installed as well. The old BCM cannot be updated to a newer software version.

 

Conversion is generally possible with the new BCM with the software version 05XX (0537, 0541). In vehicles with these software versions and standard xenon headlights, there is still a special factor that has to be taken into account: After the rear combination lamps have been encoded, the option “permanent driving light” (low beam is always activated when the engine is switched on) is no longer available. If this option is to remain active, the BCM must be updated to a newer version (SW version 0575 or later).

Once the software version has been checked, encoding takes place. For this purpose, the “long coding” is requested via the menu items Central electrics – Coding. For LED rear combination lamps, only byte 18 is changed. The BCM lists the possible changes for this byte in a sub-menu (see Figure 10).

 

In this case, the bit must be changed to “04”. Once encoding has been completed, faults will no longer be indicated.

How helpful is this article for you?

Not helpful at all

Very helpful

Please tell us what you did not like.
Many thanks. But before you go.

Sign up for our free HELLA TECH WORLD newsletter to receive the latest technical videos, car repair advice, training course information, marketing campaign details and diagnostic tips.

Show additional information on our newsletter Hide additional information on our newsletter

Register for our free HELLA TECH WORLD newsletter to stay up-to-date with the latest technical videos, car repair advice, trainings, diagnostic tips and marketing campaigns.

Together we can get cars back on the road quickly!

Please note:
You will only be subscribed to the newsletter once you have clicked on the confirmation link in the notification e-mail you will receive shortly! Data Protection | Unsubscribe

Please note:
You will only be subscribed to the newsletter once you have clicked on the confirmation link in the notification e-mail you will receive shortly!

Data Protection | Unsubscribe

Almost there!

All you need to do is confirm your sign up!
We've sent an e-mail to your email address.

Check your inbox and click on the confirmation link to start receiving HELLA TECH WORLD updates.

Wrong e-mail or no confirmation received?
Click here to enter it again.