Intake-air temperature sensor

Here you will find useful basic information and important tips relating to the intake-air temperature sensor in vehicles.

The intake-air temperature sensor might be a fairly unassuming component, but it plays a key role. Its task is to supply the engine control unit with an important measurement for correcting the mixture formation and the ignition. This page explains the functional principle of the intake-air temperature sensor, the effect of faults, and what could cause the sensor to fail. You will also find step-by-step instructions on how to check the sensor.

Important safety note The following technical information and practical tips have been compiled by HELLA in order to provide professional support to vehicle workshops in their work. The information provided on this website is intended for use by suitably qualified personnel only.

 

HOW THE INTAKE-AIR TEMPERATURE SENSOR WORKS: FUNCTIONAL PRINCIPLE

The intake-air temperature sensor determines the temperature in the suction pipe and forwards the voltage signals arising from the temperature to the control unit. This evaluates the signals and influences the mixture formation and the firing angle.

 

The resistance of the temperature sensor changes depending on the intake-air temperature. As the temperature increases, the resistance is reduced, which reduces the voltage at the sensor. The control unit evaluates these voltage values, since they are directly related to the intake-air temperature (low temperatures result in high voltage values at the sensor, and high temperatures result in low voltage values).

INTAKE-AIR TEMPERATURE SENSOR FAULTY: SYMPTOMS

A faulty intake-air temperature sensor can manifest itself in different ways through fault detection by the control unit and the resulting emergency program strategy.

 

Frequent fault symptoms are:

  • Fault code is stored, engine indicator lamp may come on
  • Problems starting
  • Reduced engine power
  • Increased fuel consumption

CAUSES OF A FAULTY IAT SENSOR: CAUSE OF FAILURE

Failure can be caused by different reasons:

  • Internal short circuits
  • Breaks in wiring
  • Wiring short circuit
  • Mechanical damage
  • Sensor tip dirty

CHECKING THE INTAKE-AIR TEMPERATURE SENSOR: TROUBLESHOOTING

TROUBLESHOOTING:

  • Read out the fault memory ✓
  • Check the electrical connections of the sensor wiring, the connector, and the sensor for correct connection, breaks, and corrosion ✓

Checks are carried out using the multimeter

Test step 1

The internal resistance of the sensor is determined. The resistance is temperature-dependent. When the engine is cold it is high-impedance, and when the engine is hot it is low-impedance.

 

Depending on the manufacturer:
25°C 2.0 – 6 KOhm or 80°C approx. 300 Ohm
Please note the special reference value specifications.

Test step 2

Check the wiring to the control unit by checking continuity and short circuit to frame for every wire to the control unit plug.

 

  1. Connect ohmmeter between temperature sensor plug and removed control unit plug. Reference value: approx. 0 Ohm (circuit diagram required for pin assignment on control unit).
  2. Check the respective pin at the sensor plug against ground using an ohmmeter and with the control unit plug removed. Reference value: >30 MOhm.

Test step 3

Check the supply voltage at the removed sensor plug using the voltmeter. This is done with the control unit plugged in and the ignition turned on. Reference value: approx. 5 V.

 

If the voltage value is not reached, the voltage supply of the control unit and the ground supply must be checked according to the circuit diagram. If these are OK, a control unit fault comes into question.

How helpful is this article for you?

Not helpful at all

Very helpful

Please tell us what you did not like.
Many thanks. But before you go.

Sign up for our free HELLA TECH WORLD newsletter to receive the latest technical videos, car repair advice, training course information, marketing campaign details and diagnostic tips.

Show additional information on our newsletter Hide additional information on our newsletter

Register for our free HELLA TECH WORLD newsletter to stay up-to-date with the latest technical videos, car repair advice, trainings, diagnostic tips and marketing campaigns.

Together we can get cars back on the road quickly!

Please note:
You will only be subscribed to the newsletter once you have clicked on the confirmation link in the notification e-mail you will receive shortly!

Data Protection | Unsubscribe

Please note:
You will only be subscribed to the newsletter once you have clicked on the confirmation link in the notification e-mail you will receive shortly!

Data Protection | Unsubscribe

Almost there!

All you need to do is confirm your sign up!
We've sent an e-mail to your email address.

Check your inbox and click on the confirmation link to start receiving HELLA TECH WORLD updates.

Wrong e-mail or no confirmation received?
Click here to enter it again.